Skip to content

In business 14 years. Free roof inspection, clear updates

(317) 793-2581
(317) 793-2581

ServicesMetal Roofing

Metal Roofing in Cumberland

A metal roof is a long-term choice, and the details decide how well it lasts. We install standing seam and panel systems with careful flashing and trim. We protect your yard while we work and keep you informed from the first measurement to the final walk-around.

Roofer in a safety harness kneeling on a roof, driving fasteners into dark standing-seam metal panels, with a ladder against the gutter and bare trees behind

When Metal Is the Right Roof for Your Home

Metal sheds snow and rain quickly and handles the swing between freezing nights and mild afternoons without the granule loss that wears down asphalt. It is a good fit if you plan to stay in your home for many years, if your current roof is near the end of its life, or if you simply prefer the clean lines of a standing seam profile.

It is not the answer for every house. Low slopes, complicated rooflines with many valleys, or a tight budget can point toward shingle roofing or a TPO roof instead. We start with a free inspection, look at the decking, the pitch and how the roof drains, and then give you an honest recommendation before anyone talks about panels.

What Our Metal Roofing Work Includes

Standing seam or exposed-fastener panels
Standing seam uses hidden clips that let each panel expand and contract with temperature, with no screws through the face. Exposed-fastener panels cost less and suit simpler roofs. We explain the tradeoffs on your roof specifically.
Deck check and underlayment
We inspect the decking for soft or delaminated sheathing and replace what is failing. A synthetic or high-temperature underlayment goes down beneath the metal, and we add ice and water barrier at the eaves and valleys.
Flashing, closures and trim
Most metal roof leaks start at chimneys, pipe boots and wall transitions, not in the panels. We bend and fit trim for each of those spots and seal ridge and eave closures so wind-driven rain and insects stay out.
Ventilation and snow guards
Balanced intake and ridge ventilation keeps condensation from forming on the underside of the panels. Where sliding snow could land on a walkway or deck, we can add snow guards.
Protection and cleanup
Tarps and plywood cover plantings, patios and the driveway edge. Cutting metal leaves small shavings that rust-stain concrete, so we sweep them up along with a magnet pass for screws and clips.

Signs It May Be Time to Consider Metal

  • Your shingles are wearing out again

    Curling tabs, bare spots and granules in the gutters mean the asphalt is aging. If you are facing a second or third replacement, metal can be the last roof you buy for a long while.

  • Ice dams form every winter

    Metal sheds snow faster than shingles, and paired with the right ventilation and eave protection, it reduces the meltwater that backs up under the roof edge.

  • Loose or leaking screws on an existing metal roof

    Older panel roofs rely on rubber washers that harden and crack with sun exposure. Rust streaks around fasteners or drips after heavy rain usually mean the screws need attention or the panels are due for replacement.

  • You want a roof that holds its color

    Quality metal finishes resist chalking and fading far longer than painted siding or older roofing. If a faded roof has been bothering you, it is worth looking at panel colors.

How a Metal Roof Installation Goes

  1. 1

    Free inspection and measurements

    We walk the roof, check the attic for moisture and ventilation, and measure every plane, valley and penetration. You get a written estimate with each item listed, and we go over panel profiles and colors with you.

  2. 2

    Ordering and scheduling

    Panels are often cut to length for your roof, so there is a short lead time. We confirm the start date with you, explain where materials and the dumpster will go, and pull the permit where it is required.

  3. 3

    Tear-off and preparation

    Before anything comes off, we cover beds, shrubs and the areas near the house. We remove the old roof one section at a time, repair the decking and lay underlayment so your home stays dry each night.

  4. 4

    Panels, trim and final walk-around

    Panels go on with clips or fasteners spaced to the manufacturer's pattern, followed by flashing, ridge cap and trim. When the roof is done we clean the yard and walk the property with you so you can see the finished work up close.

Roofer in a harness and tool belt on an extension ladder at the eaves, photographing worn asphalt shingles and roof vents on a sided house, with a blue tarp below

What Shapes the Cost of a Metal Roof

Metal asks for a larger investment at the start than asphalt, and two metal roofs can be priced quite differently. Our written estimate breaks the work into line items, from panels and trim to decking repairs, so nothing is folded into a single lump sum. Financing is available if you would rather pay over time.

Panel system and gauge
Standing seam with concealed clips calls for more material and more hours on the roof than exposed-fastener panels. Heavier gauges and premium paint finishes also raise the price.
Roof shape
Each valley, hip, dormer and chimney needs trim bent and fitted by hand. A plain gable roof comes in well below a roof with many angles and transitions.
Condition of the decking
Metal panels need a solid base, so any sheathing that has softened or begun to rot is replaced before they go on. We photograph those boards for you first, and the estimate states how that repair is charged.
Tear-off and layers
Stripping a single layer of shingles is ordinary work. Two or more layers, or an old roof that is stubborn to remove, means extra labor and more disposal.

Metal Roofing Questions

Something not covered here? (317) 793-2581

Will we hear the rain more with a metal roof?

Not by much. Installed on a solid wood deck with underlayment beneath it, a metal roof sounds close to what you hear with shingles today. The drumming people picture comes from barns and sheds where panels sit on open framing. The insulation in your attic softens the sound further.

Can metal go right over my existing shingles?

Sometimes, though we usually suggest a tear-off. Taking the shingles off lets us check and repair the decking, and it keeps moisture from getting trapped between the old and new layers. If an overlay is reasonable for your roof, we will say so and walk you through what you give up.

Will hail dent a metal roof?

Large hail can leave cosmetic dents, more so on thinner panels, but a dented panel still sheds water. Heavier gauges and some textured profiles hide hail marks better. If a storm does damage your roof, our storm damage repair page explains how we work with homeowners and insurance companies on claims.

Does a metal roof attract lightning?

No. The material on your roof has no effect on where lightning strikes. If a strike ever does reach your home, metal will not catch fire the way wood or asphalt can.

How long does installation take?

Most homes need a few working days once the panels arrive, depending on the roof's size, how many angles it has and the weather. We lay out a realistic schedule before we start and check in with you at the end of each workday.

See Whether Metal Suits Your Roof

We will inspect the decking, ventilation and pitch, then explain your options plainly. If shingles or another system fits better, we will tell you.